| |
***********************************************************************************
Acta metallurgica
sinica vol.16-2003
***********************************************************************************
No.1
1. Study on the tensile fatigue damage of quasi-isotropic composite
laminates
2. Heat treatment strengthening effects of rare earths on mg-9al alloy
3. Quantitative study on galvanic effects during cavitation damage
of 1cr13 stainless steel
4. Electrochemical noise features of pure aluminum during pitting
corrosion in neutral nacl solution
5. Determination of blank holder force in sheet metal deep drawing
process
6. Investigation on fracture behavior for welded joint of new generation
fine grained steel ss400
7. Galvanic corrosion and protection of gecm/ly12cz couples under
different atmospheric exposure conditions
8. Experimental testing of draw-bead restraining force in sheet metal
forming
9. Heat treating of sintered fe-1.5mo-0.7c steels and their sliding
wear behavior
10. Evolution of as-cast microstructures of 356 aluminium alloy cast
by liquidus casting
11. Effect of carbon content on microstructure and properties of high
strength and high elongation steels
12. Plastic deformation behavior of electroformed copper liner of
shaped charge at different strain rates |
|
No.2
1. A study on the behaviour of gallium in the ironmaking process
2. The influence of precursor variables on the phase formation,
microstructure and transport property of bi-2223/ag tapes
3. Research on the selection of friction models in the finite element
simulation of warm extrusion
4. Hot ductility of 304hc stainless steel and the model of resistance
to deformation
5. Effect of testing environment on fracturing behavior of fe3si
based alloy
6. Research on the warm forging of aluminum alloys:development of
a formula to describe the softening behavior of a2011 in forging
process
7. Purification of cobalt anolyte using the novel solvent extraction
system
8. Research on chemical composition and microstructure of newly-developed
high strength and high elongation steels
9. Study on the variation mechanism of carbon content of liquid
iron in melting gasifier
10. Formation of fe-n compounds by laser nitridation in an atmospheric
ambient
11. Microstructures and the structure stability of inconel 725,
a new age-hardenable corrosion resistant superalloy
12. Microstructure and properties of cucr25 alloys with different
ni content
|
No.3
1. Precipitation behavior in a cu-sn-ni-zn-p lead frame material
2. Study on nanometer zinc particles fabricated by gas evaporation
method
3. Three-dimensional visu alization of degenerate ferrite formed below
ttt-diagram bay in an fe-c-mo alloy
4. Antimony grain boundary segregation and its suppression by cerium
in fe-2%mn-sb structural steels
5. The hot deformation behavior and dynamic recrystallization model
of 35crmo steel
6. Microstructure and electrochemical characteristics of zr0.9
7. Ti0.1(ni1.1mn0.7v0.2)x metal hydride electrode
8. Dynamic model and simulation of eaf steelmaking process
9. Mathematical modelling of phase transformation from hot-deformed
austenite in low carbon steels
10. Effect of cr and al content on the stacking fault energy in γ-fe-mn
alloys
11. Superplasticity in sicw/zk60 composite
12. Martensite and reverse transformation in prestrained tini shape
memory alloy thin film
13. Mg-ni thin film-a potential negative electrode for nikel-metal
hydride battery
14. History and recent developments of terahertz wave generation
15. Magnetoresistance effect observed in fe/mo multilayers prepared
by electron beam evaporation
16. Microstructure analysis and mechanical properties of zn-al alloy
rod produced by heated mold continuous casting |
|
No.4
1. Numerical characterization of current-induced changes in surface
morphology of thin ag films
2. Preparation of high thermal expansion coefficient porcelains
fused to metals
3. Nano-multilayers with high perpendicular anisotropy for magnetic
recording
4. Corrosion behavior of cu-nb and ni-nb amorphous films prepared
by ion beam assisted deposition
5. Study on composition, microstructure and hardness of dlc films
by vcad
6. High-current pulsed electron beam: rapid surface alloying and
wear resistance improvement
7. Preparation and properties of ni-cr and fe-cr-al films by vacuum
evaporation
8. Electroanalytical applications of carboxyl-modified carbon nanotube
film electrodes
9. Electrochemical investigation on carbon nanotube film with different
pretreatments
10. Influences of density and dimension of carbon nanotubes on their
field emission
11. Preparation and characterization of poly-crystalline silicon
thin film
12. Effect of annealing treatment on the structure of cds films
13. Electrochemical features during pitting corrosion of ly12 aluminum
alloy in different neutral solutions
|
| No.5
1. Giant magneto-impedance
of patterned fesib/cu/fesib tri-layer films
2. Study of ag diffusion into cu single crystals by rutherford backscattering
spectrometry
3. Microstructural evolution of as-cast za27 alloy during compressive
creep
4. A general constitutive relation for fatigue crack growth analysis
of metal structures
5. Study of anodic overvoltage in neodymium electrolysis
6. Afm study on the morphological change of zn electrodeposit
7. Grain-boundary precipitation under irradiation in dilute binary
alloys
8. The reinforcing mechanism of tib2 in tib2/a357 composite
9. Research on as-cast grain refining technology by inoculating
clean steel with titanium oxide
10. Influence of processing on shape memory effect of fe-mn-si-ni-c-re
shape memory alloy
11. Revised k-ε turbulence model in electromagnetic continuous casting
of melt
12. Phase transformation behavior and microstructure observation
of nb-ru high temperature shape memory alloy
13. Studies on primary crystallization of rapidly quenched al-ni-cu-nd
metallic glass by using high resolution trasmission electron microscopy
14. Preparation of multi-walled carbon nanotubes using nio catalyst
synthesized by hydrothermal method
?/font>
|
No.6
1. Study on preparation, complex permittivity,permeability and microwave
properties of baznzco2- zfe16o27/sio2 microcrystalline glass ceramics
2. Extraction kinetics of yttrium with purified cyanex 923 from nitrate
medium
3. Electrochemical measurements of component activities in metallurgical
slags
4. Martensitic transformation and thermal stability in cu-al-co and
cu-al-zr alloys
5. Study on granulation mechanisms of γ+(fe,mn)3c eutectics in austenite
steel composites
6. Review and prospect of high strength low alloy trip steel
7. Formation of siliconized layer on tial-based alloy and the oxidation
resistance
8. Dynamic strain aging behavior of k40s alloy
9. Influence of tin on the hot ductility of a low-carbon steel
10. Preparation study of semi-solid 60si2mn spring steel slurry
11. Multi-peak match intensity ratio method of quantitative x-ray
diffraction phase analysis
12. A computerized system on kinetic analysis and evaluation of gas/solid
reactions
13. Study on co-electrodeposition of bi-fe alloy films in organic
bath
14. Medium-range order clusters in fe-2.0%c alloy melt
15. Thermodynamic parameters in the nucleation of liquid iron
16. Study on cryogenic phase change & wear characteristic of high
speed steel
17. New achievements on the theory and technology of explosive welding
18. Constitute equations of 40cr steel under superplastic compressive
deformation
19. Artificial neural networks based gears material selection hybrid
intelligent |
Click
here to order by e-mail
|
